The BMW Part Profile-Gasket 11127581215 is a crucial component in BMW vehicles, specifically designed to seal the valve cover. This gasket ensures that oil does not leak from the valve cover, maintaining the engine’s performance and longevity. It is essential for preventing oil leaks, which can lead to engine damage and reduced efficiency.
The gasket is made from high-quality materials to withstand the high temperatures and pressures within the engine. Using a genuine BMW part like this ensures optimal fitment and reliability, contributing to the overall health and efficiency of the vehicle’s engine.
The BMW Part Profile-gasket 11127581215 is a genuine BMW part with the manufacturer part number 11-12-7-581-215. It is also known by other names such as Valve Cover Gasket and Valve Cover Gasket Set. This part is specifically designed for BMW vehicles and is used in various models including the 525i, 525xi, 530i, 530xi, and Z4 from the years 2006 to 2008.
The part is made of high-quality materials to ensure durability and proper sealing of the valve cover.
It is essential for maintaining the engine’s performance by preventing oil leaks and ensuring that the valve cover is securely sealed. The item weight is approximately 0.40 pounds.
This profile-gasket replaces the part number 11-12-7-536-785 and is crucial for the proper functioning of the engine. It is recommended to check the fitment for your specific vehicle model before purchasing to ensure compatibility.
Profile-gasket 11127581215 fits the following BMW models and years:
2006-2008 BMW 323i Sedan (E90)
2006-2008 BMW 325i Sedan (E90)
2006-2008 BMW 325xi Sedan (E90), Wagon (E91)
2006-2008 BMW 330i Sedan (E90)
2006-2008 BMW 330xi Sedan (E90)
2006-2007 BMW 525i Sedan (E60)
2006-2007 BMW 525xi Sedan (E60)
2006-2007 BMW 530i Sedan (E60)
2006-2007 BMW 530xi Sedan (E60), Wagon (E61)
2006-2008 BMW Z4 Coupe 3.0si (E86), Roadster 3.0i (E85), Roadster 3.0si (E85)
Preparation: Ensure the engine is cool and disconnect the battery. Remove any components obstructing access to the valve cover, such as the air intake and engine cover.
Drain Oil: Place an oil drain pan under the valve cover and remove the oil filler cap. Open the drain plug to let the oil drain out completely.
Remove Valve Cover Bolts: Using a socket wrench, remove the bolts securing the valve cover to the engine.
Keep track of the bolts and their locations.
Lift Valve Cover: Carefully lift the valve cover off the engine. You may need to wiggle it slightly to break the seal.
Remove Old Gasket: Scrape off the old gasket material from the valve cover and the engine surface. Ensure the surfaces are clean and free of debris.
Install New Gasket: Place the new Profile-gasket 11127581215 onto the valve cover, aligning it properly with the bolt holes.
Reattach Valve Cover: Position the valve cover back onto the engine, ensuring the new gasket is properly seated.
Reinstall the bolts and tighten them to the manufacturer’s specified torque.
Reconnect Components: Reattach any components you removed earlier, such as the air intake and engine cover.
Refill Oil: Replace the oil drain plug and refill the engine with the appropriate amount of oil. Reconnect the battery and start the engine to check for any leaks.
Final Check: Let the engine run for a few minutes, then turn it off and check for any oil leaks around the valve cover. Tighten any bolts if necessary.
Clean Up: Dispose of the old oil and gasket material properly.
Clean any tools and the work area.
Test Drive: Take the vehicle for a short test drive to ensure everything is functioning correctly.
I hope this helps!
Regular Inspection: Check the gasket for any signs of wear, leaks, or damage during routine maintenance.
Proper Torque: Ensure all bolts are torqued to the manufacturer’s specifications to avoid over-tightening or under-tightening.
Clean Surfaces: Before installation, clean the mating surfaces of the cylinder head and valve cover to remove any debris or old gasket material.
Use Quality Tools: Use the correct tools and genuine parts to avoid damaging the gasket during installation.
Avoid Overheating: Ensure the engine is not overheating, as excessive heat can cause the gasket to degrade faster.
Replace When Necessary: Replace the gasket at the recommended intervals or if any issues are detected during inspections.
The BMW Part Profile-Gasket 11127581215 is a crucial component that seals the valve cover, preventing oil leaks and maintaining engine performance. It’s made from high-quality materials to withstand engine temperatures and pressures. Using a genuine BMW part ensures optimal fitment and reliability.
This gasket fits various BMW models, including the 323i, 325i, 330i, and Z4, from 2006 to 2008. To install it, follow these steps: drain oil, remove valve cover bolts, lift the valve cover, scrape off old gasket material, install the new gasket, reattach the valve cover, reconnect components, refill oil, and perform a final check.
Regular inspection, proper torque, clean surfaces, quality tools, avoiding overheating, and replacing when necessary are essential for maintaining the gasket’s performance. Using the correct part is crucial for optimal engine performance, and this gasket is specifically designed to meet BMW’s standards.
