The BMW Underbody Panelling, Side Right (Part Number: 51757258050) is a crucial component designed to protect the vehicle’s underbody from damage caused by road debris, moisture, and other environmental elements. This part is typically installed on the passenger side of the vehicle and serves as a shield, preventing dirt and water from entering sensitive areas under the car. By providing this layer of protection, the underbody panelling helps maintain the vehicle’s structural integrity and performance, ensuring a longer lifespan and reducing the risk of corrosion and other damage.
Regular inspection and maintenance of this part are essential for preserving the overall health of the vehicle.
Dimensions: 29.0 x 25.8 x 7.5 inches
Material: Steel
Compatibility: Fits 2012-2020 BMW models including 320i, 328i, 335i, 330e, 330i, 328d, 320d, 318d, 318i, 418d, 420d, 425d, 428i, 430d, 435i, 440i, 320iX, 328iX, 335iX, 330iX, 418iX, 420iX, 425iX, 430iX, 435dX, 440iX.
Screwdriver set
Socket wrench set
Torx bits
Jack and jack stands
Pliers
Safety gloves
Safety goggles
Ensure the vehicle is on a flat, stable surface.
Disconnect the battery to prevent electrical accidents.
Wear safety gloves and goggles to protect against injuries.
Follow all safety instructions provided in the vehicle’s manual.
Preparation: Park the vehicle on a flat surface and engage the parking brake. Disconnect the battery to ensure safety.
Lift the Vehicle: Use a jack to lift the vehicle and place it securely on jack stands.
Remove Old Panelling: Locate the old underbody panelling on the right side. Use a screwdriver or socket wrench to remove the screws and bolts securing it in place.
Carefully remove the old panelling.
Prepare New Panelling: Position the new underbody panelling (part number 51757258050) in place. Ensure it aligns properly with the mounting points.
Secure the Panelling: Use the screws and bolts to secure the new panelling in place. Tighten them using a screwdriver or socket wrench.
Reconnect Battery: Once the new panelling is securely installed, reconnect the vehicle’s battery.
Lower the Vehicle: Carefully lower the vehicle from the jack stands using the jack.
Final Check: Ensure all screws and bolts are tightened properly.
Check for any misalignment or loose parts.
Test drive the vehicle to ensure everything is functioning correctly.
Inspect the new panelling for any signs of damage or misalignment.
I hope this helps!
Regular Cleaning: Clean the underbody paneling regularly to remove dirt, mud, and debris that can accumulate and cause corrosion.
Rust Protection: Apply a rust protection spray or coating to prevent rust and corrosion, especially in areas exposed to moisture and road salt.
Inspect for Damage: Check for any signs of damage, such as cracks or holes, and repair them promptly to prevent further issues.
Secure Fasteners: Ensure all fasteners and clips are tight and secure to prevent the paneling from becoming loose or falling off.
Avoid Heavy Impact: Be cautious when driving over rough terrain or obstacles to avoid damaging the underbody paneling.
Professional Inspection: Have a professional mechanic inspect the underbody paneling during routine maintenance checks to identify and address any potential issues early on.
Common issues with the BMW Part Underbody Panelling, Side Right 51757258050 include:
Rust and Corrosion: The underbody paneling can be prone to rust and corrosion, especially in areas with high salt content in the air or frequent exposure to moisture.
Loose or Missing Fasteners: Over time, the fasteners that hold the underbody paneling in place can become loose or go missing, leading to rattling noises or parts of the paneling becoming detached.
Damaged or Bent Panels: The underbody paneling can get damaged or bent due to road debris, minor accidents, or improper handling during maintenance.
Wear and Tear: Continuous exposure to the elements and road conditions can cause the paneling to wear out, leading to cracks or holes.
Solutions for troubleshooting:
Rust and Corrosion: Inspect the paneling regularly for signs of rust. If rust is found, remove it using a rust remover or sandpaper, and then apply a rust-proof paint or primer to prevent further corrosion.
Loose or Missing Fasteners: Check all fasteners and replace any that are missing or damaged. Ensure that all fasteners are tightened properly to secure the paneling in place.
Damaged or Bent Panels: If the paneling is damaged or bent, it may need to be replaced.
Ensure that the replacement panel is the correct part number and properly aligned during installation.
Wear and Tear: Regularly inspect the paneling for any signs of wear and tear. If cracks or holes are found, repair them using appropriate materials such as plastic welding or adhesive patches. If the damage is extensive, consider replacing the paneling.
By addressing these common issues and implementing the suggested solutions, you can maintain the integrity and functionality of the BMW Part Underbody Panelling, Side Right 51757258050.
The BMW Underbody Panelling, Side Right (Part Number: 51757258050) is a crucial component that protects the vehicle’s underbody from damage caused by road debris, moisture, and other environmental elements. Regular inspection and maintenance of this part are essential for preserving the overall health of the vehicle.
The panelling helps maintain the vehicle’s structural integrity and performance, ensuring a longer lifespan and reducing the risk of corrosion and other damage. It is designed to fit 2012-2020 BMW models and comes with a steel material.
To install the new panelling, follow the step-by-step guide provided, which includes:
Regular cleaning, rust protection, inspecting for damage, securing fasteners, avoiding heavy impact, and professional inspection are also essential for maintaining the underbody paneling’s integrity.
Common issues with this part include:
Solutions for troubleshooting these issues include:
