The BMW Part Oval-head screw with washer 7147263759 is a small yet crucial component used in various BMW vehicles. This part is typically employed in securing components within the vehicle’s interior and exterior, ensuring stability and functionality. Its oval head design provides a secure fit, while the washer helps distribute the load and prevent damage to the attached parts.
Commonly found in models like the BMW 645Ci and 545i, this screw plays a vital role in maintaining the integrity of various assemblies.
Part Number: 07147263759
Alternate Part Numbers: 07-14-7-263-759, 07147119148
Description: Oval-head screw with washer
Material: Stainless steel
Dimensions: M6 x 21 mm
Weight: 0.20 pounds
Compatible Models:
2004-2020 BMW 528i
2004-2020 BMW 535i
2011-2020 BMW X3
2007-2020 BMW X5
2004-2005 BMW 645Ci
2013-2015 BMW 328i GT F34
2014-2016 BMW 328i GT xDrive N20 Engine (F34), N26 Engine (F34)
2019-2020 BMW 330i Sedan (G20)
2017-2019 BMW 330i GT xDrive F34
2019-2020 BMW 330i xDrive Sedan (G20)
2014-2016 BMW 335i GT xDrive F34
2017-2019 BMW 340i GT xDrive F34
Tools Needed:
Oval-head screw with washer (Part Number: 7147263759)
Appropriate screwdriver (usually Phillips or flathead, depending on the screw)
Torque wrench (if specified by the manufacturer)
Safety gloves
Safety goggles
Precautions:
Ensure the vehicle is turned off and the battery is disconnected to avoid electrical hazards.
Wear safety gloves and goggles to protect hands and eyes.
Work in a well-lit area to clearly see the installation site.
Installation Steps:
Locate the area where the oval-head screw with washer needs to be installed.
Align the screw with the pre-drilled hole.
Insert the screw through the washer, ensuring the washer is seated properly.
Use the screwdriver to turn the screw clockwise until it is snug.
If a torque wrench is required, use it to tighten the screw to the manufacturer’s specified torque.
Double-check the screw is secure and properly aligned.
Final Check:
Ensure the screw is tightened correctly and there is no movement.
Reconnect the battery and test the installation to ensure everything is functioning properly.
Clean Up:
Remove any tools and clean the work area.
Dispose of any packaging materials responsibly.
By following these steps, you can successfully install the BMW Part Oval-head screw with washer 7147263759.
Regular Inspection: Check the screw and washer for any signs of wear, corrosion, or damage. Replace them if any issues are found.
Proper Torque: Ensure the screw is tightened to the manufacturer’s specified torque to avoid over-tightening or under-tightening.
Lubrication: Apply a small amount of anti-seize lubricant to the threads to prevent seizing and make future removal easier.
Clean Environment: Keep the screw and washer clean from dirt, debris, and moisture to prevent corrosion.
Use Correct Tools: Use the appropriate tools for installation and removal to avoid stripping the screw or damaging the washer.
Periodic Re-tightening: Check and re-tighten the screw periodically, especially after exposure to vibrations or impacts.
Common issues with the BMW Part Oval-head screw with washer 7147263759 include:
Loose or missing screws: Over time, screws can become loose or fall out, leading to parts becoming unstable or detached.
Corrosion: Exposure to moisture and road salt can cause screws to corrode, making them difficult to remove or tighten.
Washer damage: Washers can become worn or damaged, reducing their effectiveness in distributing load and preventing loosening.
Incorrect installation: Using the wrong torque or improper alignment can lead to issues with the screw’s performance.
Troubleshooting advice:
Check for tightness: Regularly inspect the screws to ensure they are tight and secure. Use the appropriate torque wrench to tighten them to the manufacturer’s specifications.
Replace corroded screws: If screws are corroded, replace them with new ones. Clean the area thoroughly before installing the new screw.
Inspect washers: Examine the washers for any signs of wear or damage.
Replace them if necessary to ensure proper load distribution.
Ensure proper alignment: When installing the screws, make sure they are properly aligned to avoid cross-threading or misalignment.
By addressing these common issues and following the troubleshooting advice, you can maintain the integrity and performance of the BMW Part Oval-head screw with washer 7147263759.
The BMW Part Oval-head screw with washer 7147263759 is a crucial component that requires proper use and maintenance to ensure the integrity and performance of various assemblies in your vehicle.
It’s essential to follow the outlined guidelines for installation, inspection, and troubleshooting to avoid common issues such as loose or missing screws, corrosion, washer damage, and incorrect installation.
Regularly checking the screw’s tightness, replacing corroded screws, inspecting washers, and ensuring proper alignment can help maintain the performance of this critical component.
By following these steps, you can ensure a secure and stable vehicle that functions properly.
