The BMW Part Shaft Seal 24147571213 is a crucial component in the vehicle’s drivetrain system. It is designed to seal the selector shaft and prevent transmission fluid from leaking out. This seal ensures that the transmission system maintains the correct amount of oil, which is essential for optimal performance and longevity of the transmission.
A failing seal can lead to oil leaks, which not only cause unsightly stains but can also result in premature wear and reduced performance of the transmission. Therefore, maintaining this seal in good condition is vital for the smooth operation of the vehicle’s drivetrain system.
Technical Specifications and Dimensions:
Part Number: 24147571213
Brand: Genuine BMW
Material: NBR (Nitrile Butadiene Rubber)
Outer Diameter: 18 mm
Inner Diameter: 10 mm
Height: 5 mm
Weight: 2.10 pounds
Fitment Type: Direct Replacement
Replaces: 24-14-7-515-898, 24-52-1-207-430, 24-52-7-509-500
Transmission Compatibility: GA6HP19, GA6HP19Z, GA6HP26Z, A5S325Z, A5S310Z, A5S440Z, A5S560Z, ZF 4HP22/24, ZF 4HP22/24-EH
Dust Cover: With dust lip
Socket wrench set
Screwdrivers (flathead and Phillips)
Pry bar
Torque wrench
Drain pan
Transmission fluid
Clean rags
Safety gloves
Safety goggles
Ensure the vehicle is on a flat surface and the parking brake is engaged.
Disconnect the battery to prevent electrical accidents.
Wear safety gloves and goggles to protect hands and eyes.
Use a drain pan to catch any transmission fluid that may leak during the process.
Handle tools and parts with care to avoid injury.
Preparation: Park the vehicle on a flat surface, engage the parking brake, and disconnect the battery.
Drain Transmission Fluid: Place a drain pan under the transmission, remove the drain plug, and allow the fluid to drain completely.
Remove Transmission Pan: Use a socket wrench to remove the bolts securing the transmission pan, and carefully remove the pan to access the shaft seal.
Remove Old Seal: Use a pry bar to carefully remove the old shaft seal from its housing.
Clean Area: Clean the area around the seal housing with a clean rag to ensure no debris is left behind.
Install New Seal: Press the new shaft seal into place by hand, ensuring it is seated properly.
Reassemble Transmission: Reattach the transmission pan using the socket wrench, and refill the transmission with the appropriate amount of transmission fluid.
Reconnect Battery: Reconnect the battery and start the vehicle to check for any leaks.
Test Drive: Take the vehicle for a short test drive to ensure the new seal is functioning properly and there are no leaks.
By following these steps, you can successfully install the BMW Part Shaft Seal 24147571213. If you encounter any difficulties, it may be best to consult a professional mechanic.
Common issues with the BMW Part Shaft seal 24147571213 include leaks, which can manifest as oil stains around the transmission area. Signs of wear include dampness around the transmission pan and the selector linkage area. To troubleshoot, check for visible leaks, ensure the correct oil level, and inspect the seal for damage.
If necessary, replace the seal following proper procedures.
Regular Inspection: Check the seal for any signs of wear or leakage regularly. Early detection can prevent major issues.
Proper Lubrication: Ensure the seal and surrounding area are properly lubricated to reduce friction and wear.
Avoid Overloading: Prevent overloading the transmission to reduce stress on the seal.
Use Quality Fluids: Always use high-quality transmission fluids recommended by BMW to maintain optimal performance.
Prompt Repairs: Address any leaks or damage immediately to prevent further damage to the seal and transmission.
Professional Installation: Have the seal installed by a professional to ensure it is fitted correctly and to avoid damage during installation.
Clean Surrounding Area: Keep the area around the seal clean from dirt and debris to prevent contamination and damage.
Follow Maintenance Schedule: Adhere to BMW’s recommended maintenance schedule for your vehicle to ensure all components, including the seal, are in good condition.
The BMW Part Shaft Seal 24147571213 is a critical component in the vehicle’s drivetrain system, responsible for sealing the selector shaft and preventing transmission fluid leaks.
A failing seal can lead to oil leaks, premature wear, and reduced performance of the transmission. To maintain optimal performance and longevity, it is essential to keep this seal in good condition through regular inspection, proper lubrication, avoiding overloading, using quality fluids, prompt repairs, professional installation, cleaning the surrounding area, and adhering to BMW’s recommended maintenance schedule.
